Makita / Dolmar Chainsaw Chain Size Chart
Find the correct replacement chain for your Makita / Dolmar chainsaw. Every chain below is matched to the saw's factory pitch, gauge and bar length β the three numbers that decide fitment. This chart is part of our Complete Saw Chain Size Guide. Every chain is backed by our Guaranteed Fit promise, checked against your bar stamp before it ships.
Search by Bar Stamp β Search by Chainsaw β
Makita / Dolmar Chainsaw Chain Size Chart
Tap your Alpine chain to go straight to the product page and choose your bar length.
| Saw Model | Alpine Chain | Pitch | Gauge | Bar Sizes |
|---|---|---|---|---|
| Makita DUC150Z | Alpine EN43-S | 0.325" | 0.043" | 6" |
| Makita DUC254Z | Alpine LT43-S | 3/8" LP | 0.043" | 10" |
| Makita DUC400Z | Alpine LT43-S | 3/8" LP | 0.043" | 16" |
| Makita DUC122Z | Alpine NN50-S | 1/4" | 0.050" | 10" |
| Makita DUC302 | Alpine LT43-S | 3/8" LP | 0.043" | 12" |
| Makita DUC306Z | Alpine LT43-S | 3/8" LP | 0.043" | 12" |
| Makita UC013GZ | Alpine LT43-S | 3/8" LP | 0.043" | 14" |
| Makita UC003GZ | Alpine LT43-S | 3/8" LP | 0.043" | 12" |
| Makita DUC405Z | Alpine LT43-S | 3/8" LP | 0.043" | 16" |
| Makita DUC353Z | Alpine LT43-S | 3/8" LP | 0.043" | 14" |
| Makita EA3200S (Dolmar PS-32) | Alpine LT50-S | 3/8" LP | 0.050" | 14"/16" |
| Makita EA4300F (Dolmar PS-421) | Alpine LT50-S | 3/8" LP | 0.050" | 15"/16"/18" |
| Makita EA5000P (Dolmar PS-500) | Alpine PF50-S | 3/8" | 0.050" | 18"/20" |
| Makita EA6100P (Dolmar PS-6100) | Alpine PF50-S | 3/8" | 0.050" | 18"/20"/24" |
| Makita DCS230T (Dolmar PS-231T) | Alpine LT50-S | 3/8" LP | 0.050" | 10"/12" |
| Makita DUC355 (Twin 18V) | Alpine LT43-S | 3/8" LP | 0.043" | 14"/16" |
| Makita DUC256 (18V) | Alpine LT43-S | 3/8" LP | 0.043" | 10" |
| Makita EY401MP Pole Saw | Alpine LT50-S | 3/8" LP | 0.050" | 10" |
Model not listed, or numbers don't match? Send a photo of your bar stamp through the chat bubble and our team will confirm your exact chain before you order β our Guaranteed Fit promise.
How to Confirm Your Makita / Dolmar Chain
Bar length alone doesn't identify a chain β you also need the pitch and gauge to match. All three are usually stamped on the side of your guide bar, near the mounting bolts:
- Pitch β the size class of the chain (e.g. 3/8" LP, .325", 3/8"). Must match your drive sprocket.
- Gauge β the drive-link thickness (e.g. .043", .050", .058", .063"). Must match your bar groove. Note many Makita / Dolmar and other saws sold in Australia can differ from overseas specs, so always confirm.
- Drive links β the loop count, set by bar length and sprocket. Count them on your old chain if the stamp is worn.
Prefer to enter the numbers directly? Use Search by Bar Stamp. Only know your model? Use Search by Chainsaw.
Disclaimer: These chain sizes are specified for unmodified saws with the original driveline setup from factory. Modified saws with a different bar or sprocket will not suit the listed chain.